Thursday, November 21, 2013

Burda 05-2009-102, The Agony of Plaid Matching (aka Blazer for Tweed Ride)

Burda 05-2009-102 Thumbnail

Tweed Ride was a couple of weeks ago.  I wasn't sure I'd be able to attend so I hadn't put any thought into an outfit, but I ended up being free that day and I had one week to pull it together.  Eek!  I had just returned from vacation, before which I had engaged in an absolute orgy of sewing and was still kind of worn out.  So of course the logical thing to do was make a jacket.  A lined jacket.  In plaid.  In one week.  But last year I vowed that if I did it again this year I *would* finally make this wonderful plaid (a wool/poly blend, as it turns out) from The Carol Collection into a jacket.

I went through my BWOFs and decided I just loved Burda 05-2009-102.  Unfortunately, the smallest size it comes in is 36 and the pieces are complicated enough that I skipped grading to a 34 at the shoulders and bust as I would normally do.  Luckily, I was able to narrow the shoulders a bit on sewing and the fit in the upper part was pretty good.

Open Wedge in Back

Because the jacket was intended for a long bike ride, I wanted to make sure I had plenty of room for my broad back--reaching for the handlebars gets awfully old when your arms are restricted.  For armscye princess seams, you have to first pin the back and side back together at the stitch lines, mark your L, and then cut along the L and open out your wedge.

Completed Princess Broad Back Alteration



Put extra tissue underneath and tape it to your pattern pieces to the extent you can while the pieces are still pinned together so you preserve the same angle on both pieces, then separate them and fill in the extra area.




Fusing the Pieces



I fused all the body pieces onto lightweight, flexible interfacing (except the collar and lapel, for which I used a stiff interfacing).  I turned my cutting table aka kitchen table into a pressing table by putting an old wool blanket down, then covering the wool blanket with a white fitted sheet I keep for that purpose.  This protects the table and allows me to use lots of steam without worry.





Insert Welt into Front



When choosing the pattern, I figured that shaped front, single welt, and side with integrated pocket would be tricky.  It turns out, it was actually quite easy.  You start by sewing the welt into the front, and sewing the front pocket bag into the seam allowance.  Then you clip into the corner at the welt intersection (the photo shows the right side of one half and the wrong side of the other).

Clip Into Seam Allowance of Front at Corner

When sewing the side front to the front, open out that clip and stitch the angle as though it were straight--the pins show the "straight" line I sewed.

I was pretty amazed at how neatly it comes out.  My corner looks sharp and sits flat.  Once the front and side front were constructed I pressed them over a ham so they would look flat on a round body.  The pocket is caught into the side seam to keep it in place.

Sewing Facing to Body of Jacket-1


What turned out to be difficult in construction was sewing the facing/collar to the body of the jacket.  There is a dart hidden under the lapel to give it shape and Burda's instructions were classic BWTF.  They have you slit open the dart, and then "sew the dart and neck all at once."

I tried a LOT of different configurations before finally figuring it out.  It sounds duh to write it out, but the dart is sewn to itself, the neckline is sewn to the collar, and the lapel is sewn to the facing.  Nothing is tucked into anything else (I kept wanting to catch the lapel in the dart seam because it seemed the most logical way to put it together when all the pieces were in my hand).

You do, indeed, sew from  the bottom of the dart up over onto the *back* neck and back down the other dart.  Then you go back and complete the lapel/front neck seam separately.  If I make this again, I would try *not* cutting open the darts, sewing them as regular darts, and then sewing the neck all at once.  It seemed like they were trying to be cool and innovative rather than trying to find the best construction.

Stitch Sleeve and Side Seams

I tried a new way of setting in the sleeve based on a suggestion I saw on PR (unfortunately I can't give anyone credit, as it is impossible to find the post on the message board).  It's set in mostly in the flat, leaving the last couple inches open on either side.

Once the sleeve is set, sew the sleeve seam and the side seam and press them open.

Complete Sleeve Seam






The last step is to sew the bottom little bit of the sleeve as though it was set in, matching the sleeve underseam with the side seam.

This way you get the easier setting in in-the-flat, but you have a normal seam distribution at the underarm.  With a true in-the-flat with the sleeve/side seam sewn as one, the underarm can be a little bulkier, which isn't a problem in most cases but in a jacket fabric it might feel too much like a wad of fabric under the arm.


Organza Sleeve Head

I put in a strip of silk organza as a sleeve head.  I'm not going to lie to you: it's not cut on the bias.  The earth did not stop spinning on its axis.

I stitched the organza juuuust inside the stiching line of the sleeve's seam allowance.




Taking in the Back Seams


From the bust to the hem I had traced my usual 36 at the waist and 38 at the hip.  It was WTF huge.  Think 10 or more inches of ease at the waist.  I think Burda may have drafted this from a coat block, not a jacket block, with enough ease to wear a puffy snowsuit underneath.  Burda sizing *never* gives me trouble so this was pretty aggravating!

Because of the construction of the pocket, I could only adjust the side seam about 1/4". The rest I took out the side back and center back seam.  I took it in a total of 6 inches.  I had put so much care into the Broad Back Adjustment that I forgot to do a swayback adjustment (I was falling asleep after cutting out the jacket in the evening and started straight up when I realized this), which would have given me a little more shape at the CB seam but would not have solved the problem by a long shot.

Striped Silk Lining

It's lined in a striped tie silk from FFC.  Cidell and I bought tie silk bundles several years ago.  They may have come from an end user factory, because most of them are only about 30 inches wide with one selvage and one raw edge.

I folded this piece in half the long way rather than selvage-to-selvage, so my stripes match all the way down but the colors are off on the bottom.  I actually kind of like the effect. Brings me back to the old days of Tetris.

And now for the bad.  Part of the reason I chose this pattern is that Burda shows it in a Glen plaid and had marked "check" lines for plaid matching on the pieces.  Burda, you screwed me!!!!

 First of all, the front and back check lines did not match up to each other at the side seam.  In retrospect, this is probably mostly due to my Broad Back Adjustment, but I'm not sure that explains the full discrepancy.  I matched the lines and cut off the excess at the armscye.

Second, the check mark on the sleeve pieces had absolutely nothing to do with the check on the body pieces!!!!!!!!!  I was so mad.  I assumed they'd put the check a little above the waist on all the pieces, but the sleeve is offset from the body by almost an entire plaid motif (my plaid has a thread down the middle, alternating yellow and turquoise.  I used a yellow thread as my check.  The sleeves' turquoise thread roughly lines up with the yellow thread of the body). Because of that happy coincidence, the sleeves *almost* look like they match but they don't.

Single Layer Cutting
The lack of vertical matching is all on me (Burda doesn't give vertical check marks).  I had limited fabric and the cutting layout was a nail biter.  I cut it all one layer, then flipped the layer over to cut the other half (the photo shows the first layer flipped over onto the remaining fabric to cut out the second layer).  I had to crawl around on the floor because I needed to see my entire acreage at once.  Here's what I had left at the end--a whole two inches of length to spare.

When choosing to ignore vertical matching, I figured it would only not match vertically at the shoulders, which I could live with.  I was NOT thinking of the front/side front situation.  You don't have to tell me:  I know it looks awful.  I am trying to console myself that I probably didn't have enough fabric to get it right anyway (although they're so close to matching I probably did).  Ugh.

Buttons

Because of my lack of fabric--I couldn't cut the sleeves full length--I used the cuff variation.  I cut the cuffs and the pocket welts on the bias as accents, and so I wouldn't have to match the plaids!

My buttons don't match but I'm ok with it.  I didn't want to use the larger buttons for the cuffs and I had these smaller gold buttons in stash (both types of buttons are from a Fabric Mart 4 pound bag several years ago).



Tweed Ride

Here is the full Tweed Ride regalia (all my Tweed Ride photos are here).  The skirt is Simplicity 5914 I made several years ago and never wear because the waist is too loose--I didn't tape it and it just stretched way out.  The only fix would be to take the skirt apart and resew the seams and I have not yet made my peace with that annoyingness.  Since the low waist was going to be covered by the jacket--and the trumpet shape is good for biking--I figured it would be ok.  The hat will be reviewed soon!

Front





Although it looks costumey with the full on vintage thing going on, I think the blazer is wearable for every day (plaid matching issues aside.  UGH!).  It will be a challenge for me to find outfits to go with it because I wear so little solid color.  But how cute is it with jeans?  Too bad it's too cold for a light jacket already.  I just need one day where it doesn't get below 50 degrees at night...

I really like this pattern.  It's double-breasted without being 80s-evocative, the shaped hem in front is really nice but the higher back hemline prevents it from being dated (nothing says "I bought my suits for interviews in law school in 1999" like long jackets, not that this describes my sad suit collection, ahem).  The pocket situation is totally clever and well-drafted.  I don't know that I need two of these in my closet, but I am definitely hanging onto my tracing.  If this issue is in your archive, keep it in mind!

All photos are here and the pattern review is here.


38 comments:

Nancy K said...

Great little curvy jacket. Really flattering on your figure.

knitmachinequeen (KMQ) said...

I especially like it with the jeans and flats. Great look. TFS

Caroline said...

This is an interesting post - I'm right in the middle of sewing a coat made of Marc Jacobs fabric that has a heavy, horizontal stripe. The places where the stripes don't perfectly match are killing me! But looking at your jacket -- even with it's mis-matched plaids -- all I see is the stuff that works, its cool shape and style, and great sewing. The mis-match is way less noticeable than you think, even to a fellow sewist.

So maybe I should chill on my coat too???

Uta said...

I adore this jacket, and your tweed ride outfit is perfect, and so perfectly your style I think! I haven't dared plaid match yet (even less in a jacket or a week!) and I think you did very well.

Sandy said...

I didn't notice mismatching until you said!
This really suits you. The tweed ride outfit is especially charming. Well done!
Sandy in the UK

Mary Danielson said...

Such a cute little jacket! I can't believe you made a fully lined plaid jacket in less than a week. You're amazing!

countrygirlcouture said...

Fab jacket, and I can't believe how quickly you whipped it up--plaids and all!! Mad skillz, you haz them. ;-)

Anonymous said...

Wow....Plaids and dealing with an over-sized pattern? I would be in a corner whimpering! It looks fabulous.
Diane Drexel

Beth (SunnyGal Studio) said...

I think your plaid matching looks very good. It is a skill that comes along with practice on jackets which have so many places to match. And the bias parts give a great accent. Love it with jeans. very cute.

meg d said...

Love the jacket! Honestly, I still don't see the mismatch. The sleeves are both the same and although they don't match the body (and you have to look hard), it looks intentional. Everything is even-steven. I think it looks very sharp!

And the tights... Let's talk about those lovely mustard sweater tights!! Love love love! I saw a cute grey pair from SmartWool in LL Bean but they only came in grey. Not nearly as awesome as mustard.

catspec said...

Amazing jacket - I love it - Love the plaid and the great work you did on the matching. The buttons and other detailing are really lovely! :)

wendy said...

this is so lovely! those sidepanels are amazing. :)

Ripple Dandelion said...

I skimmed this post before reading it in detail, and I looked hard at the pictures. Even knowing that you said there was a plaid mismatch, and looking for it, I couldn't/didn't see it until I read the post in more detail to find out where it was. True story!

And the jacket is seriously cute and impressive. Would never have thought you had any fitting issues from the final result.

T. Sedai said...

Awesome! I really liked this jacket in that issue so all your construction tips will be useful to me, if I ever get around to sewing this pattern. Your version is super cute though! Love it with the rest of your Tweed Ride regalia, but I think it looks great with jeans too.

Adelaide B said...

I agree with everyone else. This jacket looks really good, and I don't even notice any mismatching. It may be one of those things that only you will ever care about. (I have a lot of garments like that.) I've been thinking more about making a plaid garment lately, but am not quite up to it yet. I'm enjoying the thinking though.

Marie said...

I can't believe you made this jacket in a week with those fitting challenges. It looks great.

McVal said...

Adorable and I love the lining! I plan to do a jacket soon so I'm planning on going through your reviews for something on how to put the linings in as those scare the bejeebies out of me...

Dilliander said...

What a fabulous jacket and perfect for the bike ride!

Ann said...

Hey, this is Ann from the happy hour in NYC last week, hi! I had to comment because I am in love with your jacket. It looks like perfection to me. The buttons and the cuffs are fantastic. Anyway, hi, and I am superimpressed!!

Kathy said...

This really turned out beautifully. What a lovely inspiration as I've been meaning to make a woolen sort of coat much like this. Thanks for sharing!

AllisonC said...

Cute look! I think you did a great job matching the plaids, no one is going to notice that area under your sleeve. Thanks for passing on the tip about the almost sewn in flat sleeves too, must remember that one.

Jane M said...

Great result despite the frustrating notching policies at Burda. You look wonderful in it. I love that sleeve technique, very useful.

Linda said...

This is a great looking jacket. It fits you very well and I like that you can dress it up or wear it casually. Great job with the plaid fabric.

Valerie said...

Great Jacket! you are way too hard on yourself about the plaid matching. It matches in the most obvious places, which is critical. Looks super with the jeans.

Lynn said...

I think it looks fabulous--and frankly, I didn't notice the non matching plaid.

emadethis said...

The curved hem is really flattering, and the full regalia looks fantastic. The hat is amazing!

Kelly said...

How have I never heard the phrase BWTF before! Anyway, I really like your jacket! I didn't notice the plaid issues at all until you pointed them out. This sounds like such a frustrating process, though. All those fitting issues and plaid matching while on a deadline?? I'm glad it turned out so well, after all that!

SEWN said...

Love the design details on this jacket. Super cute on you.

Mary said...

I just see you in your adorable jacket-no mis-matching at all. True. Give yourself bonus points for making a plaid, lined jacket in a week. And working. And eating. And resting...

SheriNJ said...

Love this look on you. So flattering.

Trumbelina said...

Plaid-matching schmaid-matching. The jacket is awesome, period. I hope you get a lot of wear out of it. Your tweed ride outfit is fantastic. I love the colour combo.

Kristy said...

Nothing like a deadline to motivate you to sew a complicated and involved project, right?! It's a lovely pattern, the curved seams and hem on the front are interesting. I like your plaid worn with jeans, very casual chic

glorm said...

That jacket looks good on you. I'm impressed with how well you took care of the problem areas.

I also need a broad back adjustment and use the method you showed. What do you do to make the side seams match? In this case you trimmed the underarm seam because of the plaid. What is your usual way of handling this? I checked previous blog entries from you and couldn't find that info. Thanks.

Digs said...

Super jacket, and I adore the fascinator hat with it! Way to go!!!

Carolyn (cmarie12) said...

I think the plaid matching on this jacket is fine. Nothing glaring that makes your eye go to it...I really like the jacket with the jeans. A nice casual wear look!

Joy said...

This turned out amazing. 1 week to match plaids, do fit adjustments, and line a jacket? Sure, no problem!

If/when I venture into the waters of fitted jacketing, I'm not sure I'll browse through my Burdas (:

Cennetta said...

It's been a while since I was able to do some serious blogging. I'm happy that I have time now. You continue to create beautiful garments. This jacket is well made and fits you. Thanks for the continued inspiration.

senaSews said...

The jacket is beautiful. It's such a nice style on you. Don't mind the plaid offset. No one else but you sees it. And you made a plaid jacket in a week. That' pretty amazing!