Burda 06-2013-128, Double Layer Tank Dress

For some reason I was struck by Burda 06-2013-128 when the magazine arrived.  It looked cute and easy to wear--and easy to sew, too, which can be a bonus sometimes.  I decided to add it to my sewing for my trip to Greece.

I didn't do the waistline casing (actually, I couldn't even tell from the instructions whether you were supposed to do a casing or use elastic thread in the bobbin).  The waistline shaping here comes solely from the sash, which I tied loosely in the hot weather for more wearing comfort.



I finished the neckline of the pink underlayer with bias binding made from the floral outer layer.  I ironed it so that one side was longer than the other so I could put the longer side on the wrong side and sew it on in one pass.

I didn't do *perfectly* at sandwiching the body of the dress and had to rip it out in a few places where I'd missed the dress altogether, so I'm not sure it was any faster than my usual two step process, but it was an interesting experiment.



I used foldover elastic to finish the floral overlayer.  Because my fabric was a woven with no stretch I didn't stretch the elastic as I would have for a knit.  I sewed the FOE in one pass as well, and as with the bias tape it mostly worked, but I had to rip and resew a few places.

I should have stretched the FOE very gently as I was applying around the curves of the center front and back, because it doesn't sit totally flat.

I ended up sewing the outer layer to the inner layer at the center front and back to get it to lay flat, as well as in the ditch of the shoulders and the side seams under the arms for a few inches to prevent shifting.




While I was making it and even once it was done, I wasn't totally sure that the self bias tape didn't make it too juvenile.  Who knows.  It's a casual, fun, summer dress so I suppose a little Garanimals isn't the worst thing ever.

I had to drastically shorten the shoulders, 1 inch in front and 1/2 inch in back (I am short from chest to shoulder, presumably due to the small bust, so I always have to shorten the front more).  I had shortened the front shoulder about 1/4" before cutting, but obviously that was only a fraction of what it needed.  I don't usually find Burda to be incredibly long from shoulder to bust so I'm not sure what's going on with this pattern.

 Because of the shortening, which I did not do on the outer layer, my inner layer shows more than the design is intended to at the neckline and armscye.






The hemline is also very long.  I shortened it 1 1/2" before cutting, and another 1 1/2" when I put in the hem, for a total of 3 inches shorter than drafted to get a just-above-the-knee hemline.

I did narrow hems on both layers, serging the edge, then pressing under along the serging line, and finally pressing under again.  This isn't a baby hem, obviously, but I find the serger width very convenient for getting a nice even hem.






I love the idea of getting a peek of the underlay fabric at the hem.  I hemmed the two layers separately to the exact same length, and then stitched the layers together.  I considered doing a subtle high-low hem, but that seemed like too much.  So you're really only going to get an occasional glimpse as the dress is in motion, but I know the detail is there.



 I cut the center back with a seam.  I didn't add any shaping or do any swayback adjusting, but because of the width of the skirt it uses vastly less fabric.  If both pieces are cut on the fold I don't think any fabric is wide enough that you don't have to cut them from separate lengths.  Cutting the back with a seam means you need almost half as much fabric.





This is just personal preference, but I don't like how low the back neckline is.  I don't think it adds much the style, it promotes gaping, and I find it inconvenient for bra purposes.  You can still get a double layer look with a higher back neck.









My two fabrics were a good match here.  The pink underlay is an Ikea sheet purchased several years ago ($14). I bought two of these sheets several years ago.  I made the green sheet into Butterick 5320.  I love the color, the sheen, and the body of the fabric, but it wrinkles horribly.  The floral overlay is an extremely lightweight cotton batiste ($3/yd) from our epic trip to Fabric Mart last November.  It's too light use on its own for anything other than a simple top, and I wanted a dress of it.  So the sheet gives body to the batiste, and the batiste hides the sheet's wrinkles.

At first I was concerned about how sticky-outy the sheet fabric is in the skirt, but then I decided I love it.  It's almost a petticoat in itself!

With some modification to the shoulder and the back neck, I really like this pattern.  I can definitely see making it again as a single layer dress.  It's a good pattern for a large print because the front and back are each just one piece.  And you know how much I love a large print.

All photos are here and the pattern review is here.

These photos were taken in Chania, Crete.  Our trip to Greece was wonderful, fabulous, amazing, and all the superlatives.  You can see the photos from the trip here (click on Greece 2013 Slideshow to see them all compiled into one set).  There are several more new pieces to come so stay tuned...

Vogue 8870, High-Low Hem Surplice Birthday Dress

It takes me a long time to warm up to a trendy trend, like the high-low hem.  At first I hate it.  Then I am skeptical.  Then I see some cute examples.  Then I am ready. This process can take years. 

After seeing several cute iterations of this pattern on PR, I decided I could take the plunge with the high-low trend (I may be willing to do the trend, but I am not willing to butcher the English language by calling it "hi-lo") using Vogue 8870, sized XS-XXL.  I even went bold with double trending by using this ombre silk, one of the gorgeous pieces BadMomGoodMom picked up for me for a song.

After I had the dress almost done I saw this Lela Rose for Fall 2013.  It looks like my trends should last through at least next season!









I did my usual adjustments, including a broad back.  I should have been more aggressive with the broad back.  I didn't want the hassle of bringing the adjustment into the raglan sleeve, so I just did it on the bodice piece, and I don't have as much movement through the back and shoulders as I would like.



There was universal praise for this pattern among those who have sewn it, but I had an *awful* time with it.  I think the flowing silk charmeuse added a level of complexity the pattern could not take.



I had a little gaping at the back neck, which is not unusual for me.  I added a tiny dart, which took care of it.

My main issue, though was the length of the bodice.  The side seams drooped a full two inches lower than the center front and back.  I sewed it to the skirt like that thinking that once the waist was elasticized there would be some sort of miracle transformation.

There was not.

So I put the dress on inside out and tied elastic around my waist and snugged it even with the lower edge of the center front and back of the bodice, then marked on the side seams where the elastic lay, which was two inches shorter.  Then I ripped the skirt off (poor silk!), reinforced the stitch line with strips of interfacing, trimmed the sides of the bodice at my markings, and sewed it back together with the shortened side seams.  Much, much improved.

The side seams of the front bodice are cut on the bias because of the grain direction, so I assumed the problem was my carelessness in letting the seam stretch out (though the back side seam is pretty close to straight grain).  But comparing the pattern piece to the finished dress, the side seam was as drafted.  I really don't know what happened.



Part of the problem may have come in with my Small Bust Adjustment of shortening the front bodice crossover.  I probably could have shortened it half as much and not had gaping; this is *very* unusual for a Big 4 pattern.  Anyway, the front pulls up a little and it's hard to keep the shoulder seams exactly square on my shoulders.  (I did nothing to the length of the back bodice, though, and it had the same length problem there with a very high center back and the drooping side seams.)




Experimenting with the elastic in the "waist" casing, it looked best if it started and ended about 3 inches in from the side seam on the front, with the center front completely flat and unelasticized and the majority of the gathering in the back. 

It still isn't great, so I went for the universal solution to a bad waist:  the sash.  Without the sash it is just bad.

However, the Bust Pleats to Nowhere I will not take credit for.  I don't know if they are angled wrong, or too close to the center front (and I overlapped the fronts about an extra 3/4" from the design) or what.  But they do not create flattering draping over the bust.  They just create a bubble of fabric above the waistline.

Speaking of which, the waistline is way high!  It is dangerously close to empire, and I swore off empire last year, no matter how much I am tempted, because it is very of a moment for 2011 and the expiration date approacheth.

I like the raglan sleeves, though they are a tad restrictive.  The downward slope of the shoulder is pretty severe.



I finished the neckline with bias tape rather than a facing.  I used the leftover bit of white fabric from below where I cut the front skirt to make the bias tape and then dyed it using a mix of Teal (mostly), Aquamarine (a little), and Navy (just a few drops) liquid Rit dye.  I managed to get an almost perfect match for the turquoise in the fabric, much to my surprise.  In the photo at right, the dyed bias strip is above and the original fabric is below.  (Alas, an attempt to dye cotton in the same dye bath did not have good results.)




After sewing the bias tape to the right side of the neckline, I stitched the raw inside edge of the bias tape over the neckline seam allowance before pressing under.  It is kept in place by strategic hand stitches at the sleeve seams.

I cut the back skirt on the fold rather than with a CB seam, as did most everyone who made the pattern.  It required ignoring the grainline, but a seam would have interfered with the smooth ombre look of the skirt.

I lined the skirt only with silk/cotton Elegance from Martha Pullen.  This stuff is a dream for lining!  I drafted a straight across hem for the lining, rather than making it high-low as well.  It shines through a little, so maybe that was a mistake.  My pet peeve for patterns with "specialty" hemlines like this is when they do not come with a "regular" hemline marked as well.  It limits the versatility of the pattern.



It's frustrating that this dress turned out kind of meh.  I put a lot of work into it; I sewed it while my serger was in the shop so it has gorgeous French seams for everything but the waist.  It's a luscious silk.  And it will have to be my birthday dress (tomorrow!) because I had only 3 weeks to sew for the Greek islands instead of a month and a half.








When it is all dressed up with accessories, it passes for a cute dress.  But it definitely cannot stand on its own.

I like the idea of this pattern but I'm not sure I'll give it another try.  Definitely not the crossover bodice.  If the mood strikes I would try to draft a plain bodice with sleeves based on the spaghetti strap version.  I like the spaghetti strap version as is but seriously, bra.  Strapless bras are horrible.  I would recommend a stable but lightweight cotton as the best fabric; a good quality lawn would be perfect.  I think this could also work in a knit.

All photos are here and the pattern review is here.

===============

Trip sewing continues apace!  So far I have made:
-3 bikinis
-shorts
-yoga/hiking capris

-nightie

I have a knit dress done except for the hem, and a knit top about halfway done.  The last two pieces on my list are a little sweater and another knit top.  Though this is a long weekend, it will be full of birthday festivities so we'll see.

Simplicity 2369, Mock Wrap Border Print Dress

I've been meaning to get back to Simplicity 2369 (which they have issued as a seemingly identical pattern in the Amazing Fit line as 1653) for a while--it is just so flattering, and also fabric-economical compared to a full wrap dress. I had made it with the longer flutter-esque sleeve, as well as self-drafted long sleeve, but I wanted to try the cap sleeve version.



The sleeve is drafted as a two piece, with a front and back sleeve and a seam all the way down the shoulder.  I combined these into one, lining up the seam line at the hem and using a dart at the shoulder where the seamlines diverged.

After the dress was made, the sleeve was much floppier than I expected.  It's shown on the line drawing as a cap and I feel like on other people it looks snug, but mine wings out a bit.  I took some width out at the hem for next time, as you can see in the tucks at left.




I shortened the crossover a smidge, shown at right.  On the previous versions I found the crossover went all the way to the side seam, so the knot bulges out right at the side seam, widening my waist.  Shortening it slightly moves the knot into the front so it doesn't add any visual width.












The only other change I made to the pattern was to attach the tie to the left side seam (the side the crossover is attached to) so that it goes across the back.

The pattern is drafted so the tie comes out the right side to just meet the crossover.  This creates way too much weight in one place, and with the crossover a smidge too long just does not work at all.  Not to mention, you lose that nice little bit of swayback fitting!





I actually went back to the pink version, cut a longer tie out of leftover fabric, and sewed it into the left side.  It's hard to see in the busy print, but the tie goes across the back in this version as well. 

I used the tie finish on the crossover described in my first post about this pattern.  It neatly encloses the raw edges.

For the neckline, I serged on very slightly stretched clear elastic then turned under and twin needled.






I really like the way this pattern works in a border print.  The skirt is not completely straight, so the border comes to a slight peak at the side seam, but it is really not noticeable unless you get this close.













In addition to using the border at the hem, I cut the sleeve hems on the border.  The detail is pretty much lost in the busy print in wearing, but I know it's there.   I cut the ties with the border at the bottom for added visual interest.






You might recognize this fabric from my impromptu Gulf Coast bikini.  I was afraid I had screwed myself by cutting into it--the motifs are huge and really need to be centered--but luckily I had just enough to make this dress.

I even had enough fabric left over for two pairs of knickers.











I used the plush back picot elastic Ms. McCall of Brown Paper Patterns sent me for the waistline.  I love it!










Knit dresses are so easy that it feels like cheating when they turn out so flattering.  Maybe I'll just call it "efficiency."

I got several unsolicitations from strangers when I wore this for the first time, in addition to kind compliments at the DC PR meetup (and an outdoor photo session!).  Even the boyfriend spoke approvingly of "that psychedelic thing" (yes, this was meant as a compliment).

All photos are here and the pattern review is here.

======================

I'm likely to be sparse for the next month or so.  I had been planning a trip to the Greek islands at the end of September, but last week we spontaneously decided to move it up to the beginning of September.  Yay, but eep!  I have so much sewing to do!  I have one bathing suit done, another cut out, and a pair of shorts cut out.  The goal is to get those, a nightgown, a knit dress, and possibly a pair of yoga/hiking capris done in the next two weekends.  Um.  There will be more sewing than blogging going on, or at least there better be!  And then I'll be on the trip itself, which I'm thinking will be sheer bliss.

DC Area Meetup and Fabric Swap Confessional

On Saturday, Nikki acted once again as our fearless leader and organized a DC area sewing meetup!  I love these events.  It's great to be able to bring projects you're working on and get opinions, to chat about sewing, and to find new homes for fabric and patterns that need to get out of stash.










We had an awesome turnout, and took over the whole front section of the restaurant (it was empty so they didn't mind).


















The front section was convenient because there is a long bench with a ledge behind it that we used for spreading out our swapping goodies.  And there were some goodies!  One woman's excess stash is definitely another woman's treasure.















I once again failed miserably in reducing my stash by bringing swap fabrics to the meetup.  But come on, how could I resist any of these?

I wore a new dress (you can see a sneak peek in the second photo) and had a great photo shoot.  More to come on that...

All photos of the meetup are here.

DC Area Sewing Meetup TOMORROW, Saturday August 17

Why do I never think to post this in advance?

There will be a brunch meetup on Saturday, August 17 for local sewing enthusiasts.  The location is Vapiano in Chinatown, right outside the Gallery Place metro (and easy walking distance from Metro Center).  It's at 623-625 H Street NW.

Bring any fabric or patterns that you'd like to swap, or just bring yourself to hang out and chat about our latest projects.

Hope to see you there!